Scroll Top
Hoge Eng West 28, 3882 TR Putten, The Netherlands

FMVSS 108: The Federal Lighting Standard for Vehicle Safety

FMVSS 108 is Federal Motor Vehicle Safety Standard No. 108, Lamps, reflective devices and associated equipment, issued by the National Highway Traffic Safety Administration (NHTSA) and published as 49 CFR 571.108. It sets the requirements for original and replacement lamps, reflective devices and associated equipment on vehicles built or sold for US roads.

Its stated purpose is to reduce crashes, deaths and injuries by illuminating the roadway and by making vehicles conspicuous, so that their presence is perceived and their signals understood in daylight, in darkness and in reduced visibility. This guide explains which lamps the standard requires, how each lamp is specified, how compliance is certified and where military vehicles stand.

Which Vehicles and Equipment Are Covered

The standard applies to passenger cars, multipurpose passenger vehicles, trucks, buses, trailers (except pole trailers and trailer converter dollies) and motorcycles (S3.1). It also applies to retroreflective sheeting and reflex reflectors made to meet its conspicuity requirements (S3.2), and to lamps, reflective devices and associated equipment sold to replace like equipment (S3.3).

The last point matters to fleet engineers, because the standard does not stop at the vehicle factory. A replacement lamp must be designed to meet every requirement the standard sets for its lamp type and must include all the functions of the lamp it replaces; for a combination lamp, that means every function (S6.7.1.1). A rear lamp that drops a function of the original, or a combined stop and tail lamp tested only as a tail lamp, is not a compliant replacement, however well it is built.

The official text is published on the eCFR as 49 CFR 571.108. Always work from the current text, not from a copy saved years ago: the standard has been rewritten and amended several times, as the timeline further down shows.

FMVSS 108 Requirements: Lamps by Vehicle Type and Width

S6.1.1 requires every vehicle to carry at least the lamps, reflective devices and associated equipment listed for its type and size in Table I. The table is split three ways: Table I-a for passenger cars, multipurpose passenger vehicles, trucks and buses of all widths, Table I-b for trailers and Table I-c for motorcycles. For each item, the tables set the number, the colour of light, the mounting location, the mounting height and when the lamp is activated.

Every vehicle in Table I-a carries a common set: headlamps, turn signal lamps, tail lamps, stop lamps, side marker lamps, reflex reflectors, a backup lamp and a licence plate lamp, with further items such as parking lamps and the high-mounted stop lamp depending on type and size. Side marker lamps sit on almost every vehicle in the table; our LED side marker lights (Model 420022) are listed to FMVSS 108 together with SAE J592, J914 and J2042.

The decisive dimension is overall width. At 2032 mm (80 in) or more, a truck, bus or trailer must also show its size, not only its position. A driver closing on a wide vehicle at night judges its width, and whether there is room to pass, from its lamps alone. That is why the following items apply to wide vehicles:

Equipment What is required Applies to
Clearance lamps 2 amber at the front and 2 red at the rear, one each side at the same height, as high as practicable, to indicate overall width. No rear clearance lamps on a truck tractor. MPVs, trucks and buses of 2032 mm or more (Table I-a); trailers of 2032 mm or more (Table I-b)
Identification lamps 3 amber at the front and 3 red at the rear, grouped on the vertical centreline with lamp centres 152 to 305 mm (6 to 12 in) apart, as near the top as practicable. No rear identification lamps on a truck tractor. MPVs, trucks and buses of 2032 mm or more; rear set also on trailers of 2032 mm or more
Conspicuity treatment Retroreflective sheeting, reflex reflectors or a combination, as specified in S8.2 (S6.1.1.1) Trailers of 2032 mm or more with a GVWR over 4,536 kg (10,000 lb); truck tractors

This matters when a specialist body is built on a commercial chassis. The requirement follows the overall width of the completed vehicle, so a body that takes a chassis past 2032 mm also brings in clearance and identification lamps.

How Each Lamp Is Specified

Section S7 holds the signal lamp requirements, one subsection per lamp type: turn signal lamps (S7.1), tail lamps (S7.2), stop lamps (S7.3), side marker lamps (S7.4), clearance and identification lamps (S7.5), backup lamps (S7.6), licence plate lamps (S7.7), parking lamps (S7.8), high-mounted stop lamps (S7.9), daytime running lamps (S7.10) and school bus signal lamps (S7.11). Reflective devices follow in S8, associated equipment such as the headlamp beam switching device in S9, and headlighting systems in S10.

Every lamp subsection works through the same headings. For tail lamps, S7.2.1 to S7.2.14 cover number, colour of light, mounting location, mounting height, activation, effective projected luminous lens area, visibility, indicator, markings, spacing to other lamps, multiple compartments and multiple lamps, ratio, photometry and physical tests. Where a heading does not apply, the standard says so: clearance and identification lamps have no lens area, visibility, indicator, spacing or ratio requirements (S7.5).

Three of those headings carry most of the engineering. Colour and position tell other road users what a lamp means before they can see the vehicle itself. Photometry sets the luminous intensity the lamp must reach at defined test points, which decides whether it is seen at distance and from an angle. The physical tests of S14.5, such as vibration, moisture, dust and corrosion, check that it keeps doing so in service. For a military or specialist vehicle this is the point to remember: a road-compliant lamp is not automatically a field-proof one, and a ruggedised lamp is not automatically road compliant. The two qualifications are separate and both have to be documented.

Before the December 2007 rewrite, the lamp requirements depended largely on SAE standards incorporated by reference. The rewrite imported those requirements into the regulatory text, so the photometric tables now sit in the standard itself. Today 49 CFR 571.5 lists only five SAE documents incorporated by reference for FMVSS 108, all supporting items: J567b (bulb sockets), J573d (lamp bulbs and sealed units), J602 in its 1963 and 1980 versions (headlamp aiming devices), J941b (driver’s eye range) and J2009 (discharge forward lighting). Lamp function standards such as SAE J585 for tail lamps are not among them, so a datasheet that lists only SAE document numbers does not show compliance with the federal standard. How the three systems relate is set out in our article on DOT vs ECE vs SAE.

Conspicuity Marking on Trailers and Truck Tractors

Large trailers and truck tractors also carry a passive marking system. S6.1.1.1 requires each trailer of 2032 mm or more in overall width with a GVWR over 4,536 kg (10,000 lb), and each truck tractor, to be fitted with retroreflective sheeting, reflex reflectors or a combination of the two, as specified in S8.2. The requirement applies to trailers manufactured from 1 December 1993 and to truck tractors manufactured from 1 July 1997.

The reason is geometric. The side of a trailer seen across the beam of approaching headlamps is a large, dark surface, and retroreflective material returns that light towards the driver who sent it. When NHTSA extended the requirement to the rear of truck tractors in 1996, it estimated that crashes in which tractors are struck from the rear in darkness could fall by 15 to 25 percent.

Conspicuity materials have their own marking rules, set in S8.2 rather than in the general marking clause (S6.5.1.1). Our reflective vehicle tape is offered in a DOT series (B6602) for the United States and an ECE 104 series (B6632) for Europe and the UK, with red and white versions in 6/6 and 7/11 inch patterns.

DOT Marking and Self-Certification

There is no US type approval. Under 49 U.S.C. 30115 the manufacturer or distributor certifies that the vehicle or equipment complies, and may not issue that certificate if, exercising reasonable care, it has reason to know the certificate is false or misleading. For equipment, the certification may be a label or tag on the item or on the outside of its container.

The DOT symbol is how that certification usually appears on a lamp. Headlamp lenses must carry it (S6.5.1). Other lamps and reflective devices in Table I may carry it, and where they do, the symbol constitutes a certification that the item conforms (S6.5.1.2). Two consequences follow for a buyer. A tail lamp or marker without a moulded DOT symbol is not necessarily non-compliant, because it may be certified on a label or on its packaging. And a lamp with the symbol carries its maker’s claim, not a government test result. For acceptance, ask for the certification and the photometric test report behind it.

How the Standard Has Changed Since 1968

The requirements that apply to a vehicle are those in force when it was built, so the history is not academic. A lamp schedule copied from an older vehicle may cite clause numbers or SAE references that the current text no longer uses.

Standard No. 108 from the first federal rule to adaptive beams
1 January 1968
The initial Standard No. 108, published on 3 February 1967, takes effect. A revised standard, published on 16 December 1967, follows on 1 January 1969.
1 December 1993
Conspicuity treatment becomes mandatory on new trailers of 2032 mm or more in width with a GVWR over 4,536 kg, under the final rule of 10 December 1992.
1 July 1997
Rear conspicuity extended to new truck tractors, under the final rule of 8 August 1996.
4 December 2007
The rewrite is published (72 FR 68234): the text is reorganised and the requirements of the SAE standards it referenced are imported into it, without new substantive requirements. Planned for 1 September 2008, its effective date was postponed to 1 December 2009 and then to 1 December 2012.
1 December 2012
The rewritten standard takes effect, as corrected by the response to petitions for reconsideration of 8 August 2011 (76 FR 48009), which allowed voluntary early compliance from that date.
22 February 2022
A final rule permitting the certification of adaptive driving beam headlamps takes effect (87 FR 9916). Petitions for reconsideration were denied on 30 December 2024.
Sources: NHTSA interpretation of 20 August 1968; Federal Register 61 FR (8 August 1996), 72 FR 68234, NHTSA Notice 3 (November 2009), 76 FR 48009, 87 FR 9916 and 89 FR (30 December 2024).

Military Vehicles and the 571.7(c) Exemption

It is often assumed that every military vehicle must meet the federal lighting standard. The regulations say otherwise. Under 49 CFR 571.7(c), no Federal Motor Vehicle Safety Standard applies to a vehicle or item of equipment manufactured for, and sold directly to, the Armed Forces of the United States in conformity with contractual specifications.

571.7(c) exempts a contract route, not a vehicle type
Both conditions must be met: the vehicle or item is manufactured for the US Armed Forces, and it is sold directly to them under contractual specifications. A commercial design can qualify: in 1975 NHTSA told the Department of the Army that commercial construction equipment sold to the military on these terms was exempt.
The exclusion is from the FMVSS only. Where the contract specifications require compliance with the FMVSS, the vehicle must comply, and a vehicle sold to anyone other than the Armed Forces must comply with all applicable standards or hold an exemption (NHTSA, 1991).
It names the Armed Forces of the United States. Vehicles and equipment built in the US for other countries rely on the separate export provisions (49 CFR 571.7(d) and 49 U.S.C. 30112(b)(3)).
Sources: 49 CFR 571.7(c) and (d), eCFR current to 6 October 2026; NHTSA interpretations to the Department of the Army (6 June 1975) and to Harness, Dickey & Pierce on a US Navy vehicle (2 August 1991).

In practice this splits a defence fleet in two. A tactical vehicle bought under a military contract can sit outside the standard, and its lighting is whatever the contract specifies: usually road lamps for peacetime movement plus blackout and convoy lighting under military requirements such as STANAG 4381, which sit outside the federal standard. A truck, bus or trailer built for the general market and bought from commercial stock does not follow the 571.7(c) route on the face of its wording, so it should be treated as an FMVSS 108 vehicle throughout its life, including the lamps fitted when it is repaired. Where a specification is silent, write the requirement in: either certification to 49 CFR 571.108 or the military lighting requirement that replaces it.

For European fleets the question arises when vehicles are built for, registered in or exported to the United States. Within Europe a different framework applies, explained in our guide to EU vehicle lighting regulations. Where a vehicle has to satisfy both, lamps listed to both systems save a refit; our 5 x 5 inch square tail lights (Model 224), for example, list FMVSS 108, SAE and ECE compliance. For a lamp schedule built around a specific vehicle, send us its type, overall width, country of registration and the functions required at info@betalight-tactical.com.

Frequently Asked Questions

The binding text is 49 CFR 571.108, published on the eCFR and updated as amendments take effect. The Federal Register holds the rulemaking history, including the December 2007 rewrite (72 FR 68234), which explains why each requirement was reorganised. Unofficial FMVSS 108 PDF copies circulate widely and may be an older edition, so check the date of any copy against the eCFR before using it in a specification or test plan.

They govern different stages. FMVSS 108, issued by NHTSA, governs how vehicles and lamps are made and sold. The Federal Motor Carrier Safety Regulations govern commercial vehicles in operation: 49 CFR 393.11 requires every commercial motor vehicle manufactured on or after 25 December 1968 to meet, at a minimum, the requirements of FMVSS 108 in effect at the time of its manufacture. A fleet operator therefore inherits the edition of the standard that applied on the vehicle’s build date, and has to keep the lamps in that condition.

Yes, within one limit. S6.2.1 does not permit any additional lamp, reflective device or other equipment that impairs the effectiveness of the lighting the standard requires. A work light or beacon mounted where it hides a required lamp, or switched so that it can be mistaken for a signal lamp, can fall foul of it. Place supplementary lamps clear of the required lamps’ visibility zones and wire them on separate switching.

Also check out these articles!